OT Security Hardware Components

OT Security Hardware Appliance (ICP)

Component	Description
Power Indicator	Indicates when the OT Security appliance is turned on (Green) or off.
Console Port	For service or local access. Baud rate of 115200 bps with an 8N1 configuration.
USB Ports	For reimaging or upgrading the appliance in the offline mode.
Ethernet Ports	Four GbE ports used to connect to management and operational networks as follows: Port 1 – By default, this port is used for both Management (User Interface) and as the Active Query port (that communicates with the network assets). This port configuration could be changed (both during the setup and later in the Settings page) to include just the Queries. This is done in order to separate the management interface from the controllers’ network. Port 2 – Mirror port - used as the destination of the mirroring session (SPAN). This port receives a copy of the network traffic. This port has no IP address. Port 3 – if the port separation option is enabled, this port is used for management (user interface) only and can be connected to a network that is not part of the controller’s network. Port 4 - Reserved port, used by OT Security's Professional Services for remote or local support.

Note: All available network interfaces are configurable for OT Security ICP.

Rear Panel

Component	Description
Cooling Fans	Two cooling fans. Make sure that the fans are not obstructed.
Power Switch	ON/OFF switch. (Press and hold for a few seconds to turn the power off.)
Power Supply	AC power connector; 100 – 240 V AC

Package Contents

Component	Description
Two Ethernet Cables	Two standard RJ45 Ethernet cables. Use these cables to connect the OT Security appliance to the network switch.
Power Supply	AC power connector; 100 – 240 V AC.
Mount Brackets	2 x 1U rack mount brackets.

OT Security Sensor Components

Configurable Sensor

Note: This model can be mounted either on a DIN rail, or on a mounting rack (using the adapter kit). In the past, this model was referred to as the DIN Rail Sensor.

Front Panel

Component	Description
Power Indicator	Indicates when the sensor is turned on (Green) or off.
Console Port	For service or local access. Note: Baud rate of 115200 bps with an 8N1 configuration.
USB Ports	For reimaging or upgrading the appliance in the offline mode.
Ethernet Ports	Five GbE ports used to connect to management and operational networks as follows: Port 1 – Management port – used for managing the device. Port 2 – Not in use. Port 3 – Mirror port - used as the destination of the mirroring session (SPAN). This port receives a copy of the network traffic. This port has no IP address. Port 4 – Not in use. Port 5 - Not in use.

Note: All available network interfaces are configurable for OT Security Sensors.

Package Contents

Component	Description
Power Cable	A standard local AC power cable.
Power Supply	60W AC power adaptor; 100 – 240 V AC.
Ethernet Cable	A standard RJ45 Ethernet cable. Use this cable to connect the sensor to the network switch.
Mounting Ears	2 x 1U L-shaped rack mount brackets (“Ears”).
Screws Pack

Rack Mount Sensor

Note: The Rack Mount sensor is being discontinued. Instead, Tenable now offers an adapter kit that enables you to attach the Configurable Sensor model to a rack mount.

Front Panel

Component	Description
Console Port*	For service or local access.
USB Ports	For reimaging or upgrading the appliance in the offline mode.
Ethernet Ports	Four 1 GbE ports used to connect to management and operational networks as follows: Port 1 – Management port – used for managing the device. Port 2 – Mirror port - used as the destination of the mirroring session (SPAN). This port receives a copy of the network traffic. This port has no IP address. Port 3 – Not in use. Port 4 – Not in use.

Component

Description

Console Port*

For service or local access.

USB Ports

For reimaging or upgrading the appliance in the offline mode.

Ethernet Ports

Four 1 GbE ports used to connect to management and operational networks as follows:

Port 1 – Management port – used for managing the device.

Port 2 – Mirror port - used as the destination of the mirroring session (SPAN). This port receives a copy of the network traffic. This port has no IP address.

Port 3 – Not in use.

Port 4 – Not in use.

*Baud rate of 115200 bps with an 8N1 configuration.

Rear Panel

Power Button	Stand-by mode in red; Power-on mode in green.
Reset Button	Reboots the system without turning off the power.
Power Switch	ON/OFF switch. (Press and hold for a few seconds to turn the power off.)
Power Supply	AC power connector; 100 – 240 V AC

Package Contents

Component	Description
Ethernet Cable	A standard RJ45 Ethernet cable. Use this cable to connect the sensor to the network switch.
Power Cable	A standard local AC power cable.
Power Supply	60W AC power adaptor; 100 – 240 V AC.
Mount Brackets	2 x 1U L-shaped rack mount brackets.
Screws Pack

Enterprise Manager

You can deploy the OT Security EM as an appliance installed on site or on a Public or Private cloud server.

The following table shows the specifications for the various deployment methods.

Specification	On-Premises	Public Cloud
Hardware	Intel® Xeon™ D1548, 2.0 GHz 2 X 32GB DDR4, 2400 MHz Data: 2 x 2TB Fixed SATA3 HDD OS: 1 X 64 GB SSD	AWS
Form Factor	Dimensions: 438 x 44 x 321 mm Weight: 6 kg	N/A
Power	220W; Single PS Input AC 90V~264V	N/A
Cooling	CPU heatsink with fan duct 2 X cooling fans	N/A
Temperature	Operating: 0°C ~40°C/32°F ~104°F Storage: -20~70º C / -4°F ~158°F Humidity: 5% ~ 90%	N/A