Scan Status

Tenable One Vulnerability Management provides a scan status for each of your configured scans.

If the scan is in progress, Tenable One Vulnerability Management shows the number of scan tasks completed as a percentage.

For example, if you scan less than 120 IP addresses in a single scan, Tenable One Vulnerability Management creates a single scan task and the progress percentage changes from 0% to 100% when it completes.

However, if you target more than 120 IP addresses, Tenable One Vulnerability Management creates multiple scan tasks. After each task completes, the percentage changes to reflect the number of completed tasks. For example, a scan that targets 300 IP addresses is split into three scan tasks, and as each task completes, the progress bar updates the percentage to reflect the completed tasks.

Note: Pausing a scan causes Tenable One Vulnerability Management to move any completed results to processing. When you resume the scan, Tenable One Vulnerability Management creates a new scan task or tasks for incomplete results. Therefore, pausing a scan can cause the progress percentage to update.

Tip: For Tenable One Vulnerability Management scans, you can hover over the scan status to view more status information in a pop-up window, such as the number of targets scanned and the elapsed or final scan time. The window shows different information based on the scan's current status.

Tenable One Vulnerability Management scans can have the following status values:

Status	Description
Tenable One Vulnerability Management Scans Tip: The typical Tenable One Vulnerability Management scan status flow is as follows: Initializing, Running, Publishing Results, Completed.
Aborted	Either the latest run of the scan is incomplete because Tenable One Vulnerability Management or the scanner encountered problems during the run, or the scan remained queued without running for four or more hours. For more information about the problems encountered during the run, view the scan warnings.
Canceled	At user request, Tenable One Vulnerability Management successfully stopped the latest run of the scan.
Completed	The latest run of the scan is complete.
Disabled	(Triggered agent scans only) The scan configuration is disabled and does not launch scans based on the configured triggers. You can enable or disable triggered agent scan configurations in the scan table's Actions menu.
Empty	The scan is either empty (the scan is new or has yet to run) or pending (Tenable One Vulnerability Management is processing a request to run the scan).
Enabled	(Triggered agent scans only) The scan configuration is enabled and launches scans based on the configured triggers. You can enable or disable triggered agent scan configurations in the scan table's Actions menu.
Imported	A user imported the scan. You cannot run imported scans. Scan history is unavailable for imported scans.
Pausing	A user paused the scan, and Tenable One Vulnerability Management is processing the action.
Paused	At user request, Tenable One Vulnerability Management successfully paused active tasks related to the scan. The paused tasks continue to fill the task capacity of the scanner that the tasks were assigned to. Tenable One Vulnerability Management does not dispatch new tasks from a paused scan job. If the scan remains in a paused state for more than 14 days, the scan times out. Tenable One Vulnerability Management then aborts the related tasks on the scanner and categorizes the scan as aborted.
Pending	Tenable One Vulnerability Management has the scan queued to launch and is assigning scan tasks to the assigned sensors. Note: Tenable One Vulnerability Management aborts scans that remain in Pending status for more than four hours. If Tenable One Vulnerability Management aborts your scan, modify your scan schedule to reduce the number of overlapping scans. If you still have issues, contact Tenable Support.
Publishing Results	Tenable One Vulnerability Management processes and stores the scan results data for you to view and use in the Tenable One Vulnerability Management user interface. The Publishing Results status begins once the Running status reaches 100%.
Resuming	Tenable One Vulnerability Management is in the process of restarting tasks after the user resumed the scan. Tenable One Vulnerability Management instructs the scanner to start the tasks from the point at which the scan was paused. If Tenable One Vulnerability Management or the scanner encounters problems when resuming the scan, the scan fails, and Tenable One Vulnerability Management updates the scan status to aborted.
Running	The scan is currently running. While this status is shown, the scan's sensors complete their assigned scan tasks, and Tenable One Vulnerability Management processes the scan results. The progress bar shows next to the status when a scan is running. The progress bar shows the percentage of the completed tasks.
Stopping	A user stopped the scan, the scan timed out or reached the end of the configured scan window, or Tenable One Vulnerability Management is stopping the scan after all associated scan tasks are complete.